meta data for this page
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
documentation:rack_mounting [2014/11/03 09:24] – First draft mic | documentation:rack_mounting [2016/06/09 12:58] (current) – vor | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Rack mounting ====== | ====== Rack mounting ====== | ||
- | {{ : | + | The Antares version of the RECS< |
- | [[http:// | + | |
+ | The following chapter is copied from the [[http:// | ||
- | 1. Slide chassis member (smallest) is removable. Separate | + | - Slide chassis member (smallest) is removable. Separate slide members by lifting left hand side lever up, and right hand side lever down. Keep slide chassis members with original outer members. |
- | slide | + | |
- | members by lifting left hand side lever up, and right hand side | + | |
- | lever down. Keep slide chassis members with original outer | + | |
- | members. | + | |
- | + | | |
- | 2. Slide has front and rear adjustable EIA brackets. Attach front | + | |
- | brackets to outer slide member using #8-32 machine screws by | + | |
- | aligning access slots on brackets to outer member holes. Front | + | |
- | brackets can be mounted flush or 1/2" | + | |
- | [12.7 mm] back from front | + | |
- | of slide based on user needs. | + | |
- | + | ||
- | 3. Establish distance from front cabinet rail to rear cabinet rail and | + | |
- | attach rear brackets to slide. | + | |
- | **Do not** | + | |
- | fully tighten rear bracket | + | |
- | mounting screws until final adjustment is made. | + | |
- | + | ||
- | 4. Insert removable locator pin into center hole of brackets. | + | |
- | + | ||
- | 5. Slide will mount to various cabinet rails at various locations on | + | |
- | side of chassis. See illustrations at right. | + | |
- | + | ||
- | 6. Place slide into desired position and fully extend against EIA | + | |
- | rails. Locator pins will support slide and bar nut while attaching | + | |
- | screws. | + | |
- | + | ||
- | 7. Attach slide to EIA rail with #10-32 screws and fasten with bar | + | |
- | nuts. Once screws are secure, remove locator pins. Do not fully | + | |
- | tighten screws until final adjustment is made. | + | |
- | + | ||
- | 8. Mount slide chassis members (smallest) to the chassis. | + | |
- | + | ||
- | 9. With cabinet members in the open or closed position, bring ball | + | |
- | retainer to full forward position. Install chassis by engaging the | + | |
- | slide members and close completely. | + | |
- | **Locks will engage on | + | |
- | initial insertion and must be released to fully close.** | + | |
- | Check | + | |
- | slide alignment by opening and closing the chassis. Any sign of | + | |
- | binding indicates lateral stress or misalignment. | + | |
- | + | ||
- | 10. Adjust slide position until movement is smooth. Tighten all screws | + | |
- | and complete installation. | + | |
**NOTE:** | **NOTE:** | ||
- | To remove chassis, lift the lever on the left hand slide up and | + | To remove chassis, lift the lever on the left hand slide up and the lever on the right hand slide down. |
- | the lever on the right hand slide down. | + | |
+ | < | ||
+ | {{ : | ||
+ | < | ||
+ | {{ : | ||
+ | < | ||
+ | {{ : | ||
+ | < | ||
+ | {{ : |