meta data for this page
  •  

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Last revisionBoth sides next revision
documentation:rpu_interface [2014/11/10 15:47] – [Front panel connectors] micdocumentation:rpu_interface [2014/11/14 09:53] – mic
Line 10: Line 10:
  
 ^  Display  ^ Description ^ ^  Display  ^ Description ^
-| <imgcaption lcd_recs_box_rpu_192_168_13_50|LCD IP screen> +| {{:documentation:lcd_recs_box_rpu_192_168_13_50.png?nolink|}} | Shows the IP address of the RPU | 
-{{:documentation:lcd_recs_box_rpu_192_168_13_50.png?nolink|}}</imgcaption> | Shows the IP address of the RPU | +| {{:documentation:lcd_health_ok_10_psus_install.png?nolink|}} | Displays the current health status of the RPU and the number of power supplies installed. | 
-| <imgcaption lcd_health_ok_10_psus_install|LCD health screen> +| {{:documentation:lcd_2_on_15_w_oe_load.png?nolink|}}| Shows the numer of power supplies that are currenty on, and the power provided by the RPU. A percentage bar (10% steps) of the load is shown in the lower line. | 
-{{:documentation:lcd_health_ok_10_psus_install.png?nolink|}}</imgcaption> | Displays the current health status of the RPU and the number of power supplies installed. | +| {{:documentation:lcd_0_off_l_00001_e_1_on_r_00001_e.png?nolink|}}| Shows the on/off status for each power supply (0=off 1= on). A dash (“-”) indicates power supplies that are not populated or where not found. “L” and “R” mark the orientation of the display and are shown as looking onto the front panel. |
-| <imgcaption lcd_2_on_15_w_oe_load|LCD load screen> +
-{{:documentation:lcd_2_on_15_w_oe_load.png?nolink|}}</imgcaption>| Shows the numer of power supplies that are currenty on, and the power provided by the RPU. A percentage bar (10% steps) of the load is shown in the lower line. | +
-| <imgcaption lcd_0_off_l_00001_e_1_on_r_00001_e|LCD installed power supplies> +
-{{:documentation:lcd_0_off_l_00001_e_1_on_r_00001_e.png?nolink|}}</imgcaption>| Shows the on/off status for each power supply (0=off 1= on). A dash (“-”) indicates power supplies that are not populated or where not found. “L” and “R” mark the orientation of the display and are shown as looking onto the front panel. |+
  
 ===== Power connectors ===== ===== Power connectors =====
  
 The Alasco has one male C19 jack on the back that can be connected to an 230V power outlet using a C20 cable. Connect this cable to an 16A fuse, as the Alasco can require up to 3600W.\\ The Alasco has one male C19 jack on the back that can be connected to an 230V power outlet using a C20 cable. Connect this cable to an 16A fuse, as the Alasco can require up to 3600W.\\
-There are nine 12V plugs in the back, that can be connected to one or more Arnebs via the coded connectors. The upper male plug is the (-) pin and the bottom female plug is the (+) pin.+There are nine 12V plugs in the back, that can be connected to one or more Arneb****s via the coded connectors. The upper male plug is the (-) pin and the bottom female plug is the (+) pin.