meta data for this page
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revisionNext revisionBoth sides next revision | ||
doc_recs4:physical_interface [2020/03/04 13:28] – created kru | doc_recs4:physical_interface [2020/03/04 15:01] – kru | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Physical interface ====== | ====== Physical interface ====== | ||
- | ===== Front panel connectors | + | ===== Front panel ===== |
The following items are located at the front of a RECS< | The following items are located at the front of a RECS< | ||
Line 14: | Line 14: | ||
The display on the front panel of the RECS< | The display on the front panel of the RECS< | ||
- | ==== Power connectors | + | ==== Status LEDs ==== |
- | === Deneb === | + | Each carrier has a row of RGB status LEDs on it's front panel. |
+ | |||
+ | === High Performance carrier === | ||
+ | |||
+ | ^ Name ^ Color ^ Description ^ | ||
+ | | STAT | Off | Baseboard not powered or early boot problem | | ||
+ | | ::: | Green | Booting (first stage) | | ||
+ | | ::: | Red | Booting (second stage) | | ||
+ | | ::: | Blue | Ready | | ||
+ | | ETH | Off | Backplane link untested | | ||
+ | | ::: | Blue | Successfully connected to backplane | | ||
+ | | HSLL | Off | PCIe switching not ready | | ||
+ | | ::: | Green | PCIe switching initializing | | ||
+ | | ::: | Blue | PCIe switching ready | | ||
+ | | ::: | Red | PCIe switching initialization error | | ||
+ | | 1, 2, 3| Off | Node hard off | | ||
+ | | ::: | Red | Node in standby | | ||
+ | | ::: | Blue | Node on | | ||
+ | | ACT | Blue | Network activity | | ||
+ | | ::: | Red | SATA activity | | ||
+ | |||
+ | === Low Power carrier === | ||
+ | |||
+ | ^ Name ^ Color ^ Description ^ | ||
+ | | S | Off | Baseboard not powered or early boot problem | | ||
+ | | ::: | Green | Booting (first stage) | | ||
+ | | ::: | Red | Booting (second stage) | | ||
+ | | ::: | Blue | Ready | | ||
+ | | 1 - 8 | Off | Node off | | ||
+ | | ::: | Blue | Node on | | ||
+ | |||
+ | ===== Power connectors ===== | ||
+ | |||
+ | ==== Deneb ==== | ||
The Deneb has four male C14 jacks on the back that can be connected to an 230V power outlet using a standard C13 cable.\\ | The Deneb has four male C14 jacks on the back that can be connected to an 230V power outlet using a standard C13 cable.\\ | ||
The exhaust air openings in the back must be kept free. Keep that in mind when installing cables behind the Deneb. | The exhaust air openings in the back must be kept free. Keep that in mind when installing cables behind the Deneb. | ||
- | === Durin === | + | ==== Durin ==== |
The Durin has two male C14 jacks on the back that can be connected to an 230V power outlet using a standard C13 cable.\\ | The Durin has two male C14 jacks on the back that can be connected to an 230V power outlet using a standard C13 cable.\\ | ||
The exhaust air openings in the back must be kept free. Keep that in mind when installing cables behind the Deneb. | The exhaust air openings in the back must be kept free. Keep that in mind when installing cables behind the Deneb. | ||
- | |||
- | ===== Sensors ===== | ||