meta data for this page
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | Last revisionBoth sides next revision | ||
documentation:rack_mounting [2014/11/14 14:37] – mic | documentation:rack_mounting [2016/06/09 12:55] – vor | ||
---|---|---|---|
Line 3: | Line 3: | ||
The Antares version of the RECS< | The Antares version of the RECS< | ||
- | [[http:// | + | The following chapter is copied from the [[http:// |
- | >1. Slide chassis member (smallest) is removable. Separate slide members by lifting left hand side lever up, and right hand side lever down. Keep slide chassis members with original outer members. | + | 1. Slide chassis member (smallest) is removable. Separate slide members by lifting left hand side lever up, and right hand side lever down. Keep slide chassis members with original outer members. |
- | > | + | |
- | >2. Slide has front and rear adjustable EIA brackets. Attach front brackets to outer slide member using #8-32 machine screws by aligning access slots on brackets to outer member holes. Front brackets can be mounted flush or 1/2" [12.7 mm] back from front of slide based on user needs. | + | 2. Slide has front and rear adjustable EIA brackets. Attach front brackets to outer slide member using #8-32 machine screws by aligning access slots on brackets to outer member holes. Front brackets can be mounted flush or 1/2" [12.7 mm] back from front of slide based on user needs. |
- | > | + | |
- | >3. Establish distance from front cabinet rail to rear cabinet rail and attach rear brackets to slide. **Do not** fully tighten rear bracket mounting screws until final adjustment is made. | + | 3. Establish distance from front cabinet rail to rear cabinet rail and attach rear brackets to slide. **Do not** fully tighten rear bracket mounting screws until final adjustment is made. |
- | > | + | |
- | >4. Insert removable locator pin into center hole of brackets. | + | 4. Insert removable locator pin into center hole of brackets. |
- | > | + | |
- | >5. Slide will mount to various cabinet rails at various locations on side of chassis. See illustrations at right. | + | 5. Slide will mount to various cabinet rails at various locations on side of chassis. See illustrations at right. |
- | > | + | |
- | >6. Place slide into desired position and fully extend against EIA rails. Locator pins will support slide and bar nut while attaching screws. | + | 6. Place slide into desired position and fully extend against EIA rails. Locator pins will support slide and bar nut while attaching screws. |
- | > | + | |
- | >7. Attach slide to EIA rail with #10-32 screws and fasten with bar nuts. Once screws are secure, remove locator pins. Do not fully tighten screws until final adjustment is made. | + | 7. Attach slide to EIA rail with #10-32 screws and fasten with bar nuts. Once screws are secure, remove locator pins. Do not fully tighten screws until final adjustment is made. |
- | > | + | |
- | >8. Mount slide chassis members (smallest) to the chassis. | + | 8. Mount slide chassis members (smallest) to the chassis. |
- | > | + | |
- | >9. With cabinet members in the open or closed position, bring ball retainer to full forward position. Install chassis by engaging the slide members and close completely. **Locks will engage on initial insertion and must be released to fully close.** Check slide alignment by opening and closing the chassis. Any sign of binding indicates lateral stress or misalignment. | + | 9. With cabinet members in the open or closed position, bring ball retainer to full forward position. Install chassis by engaging the slide members and close completely. **Locks will engage on initial insertion and must be released to fully close.** Check slide alignment by opening and closing the chassis. Any sign of binding indicates lateral stress or misalignment. |
- | > | + | |
- | >10. Adjust slide position until movement is smooth. Tighten all screws and complete installation. | + | 10. Adjust slide position until movement is smooth. Tighten all screws and complete installation. |
- | > | + | |
- | >**NOTE:** | + | **NOTE:** |
- | >To remove chassis, lift the lever on the left hand slide up and the lever on the right hand slide down. | + | To remove chassis, lift the lever on the left hand slide up and the lever on the right hand slide down. |
< | < |